Models

RM-1
RM-2
RM-3
RM-4
RM-5
RM-6

Features

  • Refrigerated copper tubing, within the 3″ recess, around all sides—meets your toughest health department standard
  • Fully insulated for maximum efficiency and energy savings
  • Factory applied gasket—makes installation a snap and seals units to the counter top, thus eliminating seepage
  • Accommodates standard 12″ x 20″ pans with the use of separator channel(s) and pan rails, or fractional size pans with the use of optional adapter bar
  • 1-Year Parts & Labor Warranty
  • NSF Certified; UL Listed

Certifications

Classified UL EPH Custom FSE 3523Atlas Metal UL 39F7 Custom Built FSE

RM – REFRIGERATED COLD PAN (With 3" Recessed Top; NSF-7)

Pans & Cases

The RM Series refrigerated cold pan eliminates the mess and expense of ice in your cold food displays. In addition, this cold pan (9″ deep) has copper tubing wrapped around its side walls to meet the strictest health department codes. The drop-in pan can be installed in virtually any counter and can be provided as fully self-contained—just plug it in and turn it on, or remote, where there’s a need to locate the compressor at a different location.

The pan is fully insulated for maximum efficiency and energy savings, and is provided with a factory applied gasket so that it can be installed in the finest wood fixtures without marring the counter top. The pan is constructed of stainless steel and is provided with a 3/4″ stainless steel drain. The cold pan accommodates standard 12″ x 20″ pans, perfect for any cold food serving application.

Models

RM-1
RM-2
RM-3
RM-4
RM-5
RM-6

Features

  • Refrigerated copper tubing, within the 3″ recess, around all sides—meets your toughest health department standard
  • Fully insulated for maximum efficiency and energy savings
  • Factory applied gasket—makes installation a snap and seals units to the counter top, thus eliminating seepage
  • Accommodates standard 12″ x 20″ pans with the use of separator channel(s) and pan rails, or fractional size pans with the use of optional adapter bar
  • 1-Year Parts & Labor Warranty
  • NSF Certified; UL Listed

Certifications

Classified UL EPH Custom FSE 3523Atlas Metal UL 39F7 Custom Built FSE

Specifications

Top: Constructed of 18 gauge, type 304 stainless steel, die stamped with a raised perimeter bead. There shall be a solid vinyl gasket under the beaded edge to form a seal to the counter top, thus preventing seepage or marring of the counter top. Embossed mounting lugs are provided along the inner surface, 3″ down from the top, to hold the pan rails and a full set of removable separator channels in place.

Liner: The inner liner shall be 18 gauge, type 304 stainless steel with a 3″ recessed top, one piece construction, all welded, ground and polished to a uniform finish. All corners are coved with a minimum 1/4″ radius. The liner has copper tubing firmly soldered to the top 3″ on all sides. A 3/4 dia. drain with strainer, 4″ PVC nipple, and valve is provided.

Insulation: The pan is fully insulated with high density polystyrene, 1″ thick on all sides, 2″ thick on the bottom and enclosed with a 22 gauge galvanized steel outer case.

Refrigeration System: The compressor housing shall be fabricated from 14 gauge galvanized and bolted to the base of the unit. A fully self-contained condensing unit is provided with a hermetically sealed compressor and digital electronic thermostat/thermometer. The system is fully charged with CFC-free refrigerant and ready to operate.

Note: Proper ventilation must be provided in the counter.

Electrical: The unit will be wired for 15 amp, 120 volt, single phase operation with an on/off switch and pilot light. A 6′-long, 3-wire cord and plug (NEMA 5-15P) will be provided.

Rendering

*Model Shown: RM-3 – Not representative of final product

Resources

Options

Have equipment questions?

Top: Constructed of 18 gauge, type 304 stainless steel, die stamped with a raised perimeter bead. There shall be a solid vinyl gasket under the beaded edge to form a seal to the counter top, thus preventing seepage or marring of the counter top. Embossed mounting lugs are provided along the inner surface, 3″ down from the top, to hold the pan rails and a full set of removable separator channels in place.

Liner: The inner liner shall be 18 gauge, type 304 stainless steel with a 3″ recessed top, one piece construction, all welded, ground and polished to a uniform finish. All corners are coved with a minimum 1/4″ radius. The liner has copper tubing firmly soldered to the top 3″ on all sides. A 3/4 dia. drain with strainer, 4″ PVC nipple, and valve is provided.

Insulation: The pan is fully insulated with high density polystyrene, 1″ thick on all sides, 2″ thick on the bottom and enclosed with a 22 gauge galvanized steel outer case.

Refrigeration System: The compressor housing shall be fabricated from 14 gauge galvanized and bolted to the base of the unit. A fully self-contained condensing unit is provided with a hermetically sealed compressor and digital electronic thermostat/thermometer. The system is fully charged with CFC-free refrigerant and ready to operate.

Note: Proper ventilation must be provided in the counter.

Electrical: The unit will be wired for 15 amp, 120 volt, single phase operation with an on/off switch and pilot light. A 6′-long, 3-wire cord and plug (NEMA 5-15P) will be provided.

*Model Shown: RM-3 – Not representative of final product

find your personal solution
Contact Us

RECEIVE THE ATLAS UPDATE NEWSLETTER