Models

WCML-2
WCML-3
WCML-4

Features

  • Slim-Line configuration—it can install in counters only 16″ wide
  • Fully insulated for maximum efficiency and energy savings
  • Factory applied gasket makes installation a snap and seals units to the counter top, thus eliminating seepage.
  • Accommodates standard 12″x 20″ pans with the use of separator channel(s), or fractional size pans with the use of optional adapter bars
  • 1-Year Parts & Labor Warranty
  • NSF Certified and UL Listed

Certifications

NSFAtlas Metal UL 39F7 Custom Built FSE

WCML – SLIM-LINE REFRIGERATED COLD PAN (Standard Depth; Non NSF-7)

Slim Line

The slim-line design can be installed in extra narrow width counters. The unit is used with standard 12″ x 20″ pans, in the long configuration, and the overall cold pan will require only 16″ of the clear counter space! The cold pan is available in the standard 4-5/8″ depth and the 9-3/4″ full depth.

The pan is fully insulated for maximum efficiency and energy savings, and is provided with a factory applied gasket so that it can be installed in the finest wood fixtures without marring the counter top. The pan is constructed of stainless steel and is provided with a 3/4″ stainless steel drain.

Models

WCML-2
WCML-3
WCML-4

Features

  • Slim-Line configuration—it can install in counters only 16″ wide
  • Fully insulated for maximum efficiency and energy savings
  • Factory applied gasket makes installation a snap and seals units to the counter top, thus eliminating seepage.
  • Accommodates standard 12″x 20″ pans with the use of separator channel(s), or fractional size pans with the use of optional adapter bars
  • 1-Year Parts & Labor Warranty
  • NSF Certified and UL Listed

Certifications

NSFAtlas Metal UL 39F7 Custom Built FSE

Specifications

Top: Constructed of 18 gauge, type 304 stainless steel, die stamped with a raised perimeter bead. There shall be a solid vinyl gasket under the beaded edge to form a seal to the counter top, thus preventing seepage or marring of the counter top. Embossed mounting lugs are provided along the inner surface of the top to hold a full set of removable separator channels in place.

Liner: The inner liner shall be 18 gauge, type 304 stainless steel, one piece construction, all welded, ground and polished to a uniform finish. All corners are coved with a minimum 1/4″ radius. The liner has copper tubing firmly soldered to the exterior bottom. A 3/4″ dia. drain with strainer, 4″ PVC nipple, and valve is provided.

Insulation: The pan is fully insulated with high density polystyrene, 1″ thick on all sides, 1-1/2″ thick on the bottom and enclosed with a 22 gauge galvanized steel outer case.

Refrigeration System: The compressor housing shall be fabricated from 14 gauge galvanized and bolted to the base of the unit. A fully self-contained condensing unit is provided, with a hermetically sealed compressor and a thermostat control. The system is fully charged with CFC-free refrigerant and ready to operate.

Note: Proper ventilation must be provided in counter.

Electrical: The unit will be wired for 15 amp, 120 volt, single phase operation, with an on/off thermostat switch and pilot light. A 6′-long, 3-wire cord and plug (NEMA 5-15P) will be provided.

Rendering

*Model Shown: WCML-3 – Not representative of final product

Resources

Options

Have equipment questions?

Top: Constructed of 18 gauge, type 304 stainless steel, die stamped with a raised perimeter bead. There shall be a solid vinyl gasket under the beaded edge to form a seal to the counter top, thus preventing seepage or marring of the counter top. Embossed mounting lugs are provided along the inner surface of the top to hold a full set of removable separator channels in place.

Liner: The inner liner shall be 18 gauge, type 304 stainless steel, one piece construction, all welded, ground and polished to a uniform finish. All corners are coved with a minimum 1/4″ radius. The liner has copper tubing firmly soldered to the exterior bottom. A 3/4″ dia. drain with strainer, 4″ PVC nipple, and valve is provided.

Insulation: The pan is fully insulated with high density polystyrene, 1″ thick on all sides, 1-1/2″ thick on the bottom and enclosed with a 22 gauge galvanized steel outer case.

Refrigeration System: The compressor housing shall be fabricated from 14 gauge galvanized and bolted to the base of the unit. A fully self-contained condensing unit is provided, with a hermetically sealed compressor and a thermostat control. The system is fully charged with CFC-free refrigerant and ready to operate.

Note: Proper ventilation must be provided in counter.

Electrical: The unit will be wired for 15 amp, 120 volt, single phase operation, with an on/off thermostat switch and pilot light. A 6′-long, 3-wire cord and plug (NEMA 5-15P) will be provided.

*Model Shown: WCML-3 – Not representative of final product

find your personal solution
Contact Us

RECEIVE THE ATLAS UPDATE NEWSLETTER