Models

WCMDCL-2
WCMDCL-3
WCMDCL-4

Features

  • Slim-line configuration – it can install in counters only 16″ wide
  • Accommodates your deepest pan or insert—9-3/4″ deep
  • WCMDCL units have refrigerated copper tubing around all sides and base—meets your toughest health department standards
  • Fully insulated for maximum efficiency and energy savings
  • Factory applied gasket makes installation a snap and seals units to the counter top, thus eliminating seepage
  • Accommodates standard 12″ x 20″ pans with the use of separator channel(s), or fractional size pans with the use of optional adapter bars
  • 1-Year Parts & Labor Warranty
  • NSF Certified and UL Listed

Certifications

NSFAtlas Metal UL 39F7 Custom Built FSE

WCMDCL – SLIM-LINE REFRIGERATED COLD PAN (Full Depth With Side Coils; Non NSF-7)

Slim Line

The slim-line design can be installed in extra narrow width counters. The unit is used with standard 12″ x 20″ pans, in the long configuration, and the overall cold pan will require only 16″ of the clear counter space! The cold pan is available in the standard 4-5/8″ depth and the 9-3/4″ full depth.

Models

WCMDCL-2
WCMDCL-3
WCMDCL-4

Features

  • Slim-line configuration – it can install in counters only 16″ wide
  • Accommodates your deepest pan or insert—9-3/4″ deep
  • WCMDCL units have refrigerated copper tubing around all sides and base—meets your toughest health department standards
  • Fully insulated for maximum efficiency and energy savings
  • Factory applied gasket makes installation a snap and seals units to the counter top, thus eliminating seepage
  • Accommodates standard 12″ x 20″ pans with the use of separator channel(s), or fractional size pans with the use of optional adapter bars
  • 1-Year Parts & Labor Warranty
  • NSF Certified and UL Listed

Certifications

NSFAtlas Metal UL 39F7 Custom Built FSE

Specifications

Top: Constructed of 18 gauge, type 304 stainless steel, die stamped with a raised perimeter bead. There shall be a solid vinyl gasket under the beaded edge to form a seal to the counter top, thus preventing seepage or marring of the counter top. Embossed mounting lugs are provided along the inner surface of the top to hold a full set of removable separator channels in place.

Liner: The inner liner shall be 18 gauge, type 304 stainless steel, one piece construction, all welded, ground and polished to a uniform finish. All corners are coved with a minimum 1/4″ radius. The WCMDL liner has copper tubing firmly soldered to the exterior BOTTOM ONLY. The WCMDCL liner has copper tubing firmly soldered to the exterior BOTTOM AND ALL SIDES. 4″ dia. drain with strainer, 4″ PVC nipple, and valve is provided.

Insulation: The pan is fully insulated with high density polystyrene, 1″ thick on all sides, 1-1/2″ thick on the bottom and enclosed with a 22 gauge galvanized steel outer case.

Refrigeration System: The compressor housing shall be fabricated from 14 gauge galvanized angles and bolted to the base of the unit. A fully self-contained condensing unit is provided, with a hermetically sealed compressor and a thermostat control. The system is fully charged with CFC-free refrigerant and ready to operate.

Note: Proper ventilation must be provided in counter.

Electrical: The unit will be wired for 15 amp, 120 volt, single phase operation, with an on/off thermostat switch and pilot light. A 6′-long, 3-wire cord and plug (NEMA 5-15P) will be provided.

Rendering

*Model Shown: WCMDCL-3 – Not representative of final product

Resources

Options

Have equipment questions?

Top: Constructed of 18 gauge, type 304 stainless steel, die stamped with a raised perimeter bead. There shall be a solid vinyl gasket under the beaded edge to form a seal to the counter top, thus preventing seepage or marring of the counter top. Embossed mounting lugs are provided along the inner surface of the top to hold a full set of removable separator channels in place.

Liner: The inner liner shall be 18 gauge, type 304 stainless steel, one piece construction, all welded, ground and polished to a uniform finish. All corners are coved with a minimum 1/4″ radius. The WCMDL liner has copper tubing firmly soldered to the exterior BOTTOM ONLY. The WCMDCL liner has copper tubing firmly soldered to the exterior BOTTOM AND ALL SIDES. 4″ dia. drain with strainer, 4″ PVC nipple, and valve is provided.

Insulation: The pan is fully insulated with high density polystyrene, 1″ thick on all sides, 1-1/2″ thick on the bottom and enclosed with a 22 gauge galvanized steel outer case.

Refrigeration System: The compressor housing shall be fabricated from 14 gauge galvanized angles and bolted to the base of the unit. A fully self-contained condensing unit is provided, with a hermetically sealed compressor and a thermostat control. The system is fully charged with CFC-free refrigerant and ready to operate.

Note: Proper ventilation must be provided in counter.

Electrical: The unit will be wired for 15 amp, 120 volt, single phase operation, with an on/off thermostat switch and pilot light. A 6′-long, 3-wire cord and plug (NEMA 5-15P) will be provided.

*Model Shown: WCMDCL-3 – Not representative of final product

find your personal solution
Contact Us

RECEIVE THE ATLAS UPDATE NEWSLETTER